详情请进入 湖南阳光电子学校 已关注:人 咨询电话:0731-85579057 微信号:yp941688, yp94168
掌握这几点电焊技术,你也可以成为焊接高手!
2022-03-11 13:11 来源: 河北华洋钢管有限公司
原标题:掌握这几点电焊技术,你也可以成为焊接高手!
管道焊接有两种方式:
There are two ways of pipe welding:
2、连弧法,通常大型管道是焊接的。首先点焊要做到打底。记得底部不要太厚,这样方便盖面。连续焊接时,调节电流主要看原材料的厚度。一般将电流应调整到比点焊小40至50左右。
2. Continuous arc method, usually large pipes are welded. First of all, the spot welding shall be done with the backing. Remember not to be too thick at the bottom, so it is convenient to cover the surface. During continuous welding, adjusting the current mainly depends on the thickness of raw materials. Generally, the current should be adjusted to about 40 to 50 less than that of spot welding.
电流
electric current
电流很重要,焊接前一定要反复调整适合的电流,只有这样才能焊接出满意的效果。
The current is very important. The appropriate current must be adjusted repeatedly before welding. Only in this way can we achieve satisfactory welding results.
平仰立:这是焊工最基本最简单的操作。
Horizontal, upward and vertical: This is the most basic and simple for welders.
平:把药皮焊条90度放在焊把中间的口上,焊接均匀,这样焊出来的平缝100%好看。
Flat: put the coated electrode at 90 degrees on the middle opening of the welding handle and weld evenly, so that the welded flat seam is 100% good-looking.
仰:慢慢焊,点焊一点,压一点,注意熔池。注意避免烫伤,烫伤是不可避免的,除非你有金钟罩。
Tilt: weld slowly, spot weld a little, press a little, and pay attention to the molten pool. Be careful to avoid scalding. Scalding is inevitable unless you have a golden bell jar.
立;可以像管子一样点焊,这一个是三个中最难的。个人建议大家站着焊的时候用点焊,压一个焊条不要急着快,焊下一个的时候记得把接头部分的药皮打掉。
stand; It can be spot welded like a pipe. This one is the most difficult of the three, even arc welding. Personally, I suggest you use spot welding when standing. Don't rush to stabilize one electrode. Remember to knock off the coating of the joint when welding the next one.返回搜狐,查看更多
责任编辑:
声明:该文观点仅代表作者本人,搜狐号系信息发布平台,搜狐仅提供信息存储空间服务。
。原州电焊培训学校,原州电焊培训班,原州电焊学校,原州学电焊的学校,原州电焊培训哪里好,原州电焊培训学校,原州电焊短期培训班,原州电焊培训学校地址,原州学电焊培训,原州电焊培训哪里好,原州电焊培训班,原州电焊技术培训.(编辑:hnygdzxx888)(整理:原州电焊培训学校)
湖南阳光电子学校教学特色